Leading 10 usual forklift accidents ， forklift procedure need to pay attention to these issues ！.

Do not ignore the forklift at work. If the operation is not good, there will be major mishaps in minutes, and there are lots of crashes entailing forklifts.

Situation 1: The forklift freight obstructed the vehicle driver's view, and the individual ahead can not be located, causing a moving mishap.
Situation 2: In order to preserve the balance of the forklift when lifting heavy goods, the employees utilized their body weight as the weight, which virtually created casualties.
Situation 3: The width of the forklift cargo exceeds the allowable size of the course and holds on the roadside shelf, which almost causes an crash.
Situation 4: Forklift is speeding and rolls over throughout a turn.
Instance 5: The forklift motorist did not discover the pedestrian, and the pedestrian did not discover the forklift.
Case 6: The forklift raises the workers illegally, the forklift driver does not put on the seat belt, the forklift lifter falls and the vehicle driver is squashed when the forklift rolls over.
Case 7: The forklift vehicle driver did not use a seat belt and dropped from the automobile when it rolled over and was squashed.
Forklift operation should pay attention to these issues ：.

Begin.
1. Prior to beginning, observe the surroundings, and after validating that there are no challenges that prevent the security of driving, honk the horn initially and then begin.
2. For cars with hydraulic (air pressure) brakes, the brake hydraulic stress (air pressure) gauge must be risk-free before beginning.
3. When the forklift starts with a tons, the driver must first verify that the load is steady and dependable.
4. The beginning should be slow-moving and stable.

Driving.
1. When driving, the elevation between the bottom end of the fork and the ground must be maintained 300mm-400mm, and the mast must be tilted backwards. .
2. Do not raise the fork too expensive when driving. When getting in and leaving the job website or while driving, take care that there will be no challenges overhead. When the load is traveling, the fork has to not be raised too expensive, which will certainly influence the stability of the forklift. .
3. After discharging, the fork needs to be lowered to the typical driving setting prior to driving. .
4. When turning, if there are pedestrians or cars close by, the driving signal needs to be released first. High-speed sharp turns are forbidden. High-speed doglegs will certainly cause the car to lose side security and topple. .
5. When the forklift is downhill, it is purely forbidden to turn off the flame and slide, and it is prohibited to brake unexpectedly while driving with lots unless there are unique circumstances.
6. When the forklift is running, it should follow the web traffic rules in the manufacturing facility and need to maintain a particular safety and security range from the vehicle in front. .
7. When the forklift is running, the load should be in the lowest setting that does not impede the driving, and the gantry ought to be appropriately tilted back. The tons shall not be raised except when stacking or filling. .
8. The elevation of the lots have to not obstruct the motorist's sight. In special situations, when the item affects the forward vision, drive at a reduced rate when turning around.
9. It is prohibited to turn on the ramp, nor to drive throughout the ramp. .
10. The secure driving rate of the forklift in the factory area is 5 km/h, and it has to drive securely at a reduced speed when entering the manufacturing workshop location. .
11. When the forklift is lifted, lifted or driven, it is restricted for employees to base on the fork to hold items and play a stabilizing duty. .
12. If issues are found, they will certainly be fixed and reported in a timely fashion, and they will certainly never run with health problems or conceal them.

loading and discharging.
1. When fork-loading products, the distance in between the two forks should be adjusted as required to make the load of both forks balanced and not skewed, and one side of the thing ought to protest the rack. .
2. It is forbidden to collaborate with a single fork or make use of a fork top or draw. In special scenarios, safety indication should be established to remind bordering pedestrians. .
3. In the process of packing and dumping products, the forklift must be stopped with the brake. .
4. The rate of the automobile should be sluggish and steady. Take care not to roll the wheels on the dunnage, so as not to stretch the rolled items and hurt individuals. .
5. When making use of a fork to fork the goods, the fork ought to be as deep as feasible under the load, and it must be noted that the fork idea need to not touch other items or objects. The tons needs to be stabilized with very little back tilt of the gantry so that the tons does not glide backwards. The pole can be tilted onward slightly when the tons is decreased to allow for easy positioning of the lots and extraction of the forks. .
6. It is prohibited to fork products at broadband and collide with difficult items with the fork head. .
7. When the forklift is functioning, it is forbidden for people to stand around the fork, so regarding stay clear of the collapse of the goods and injure people. .
8. Overloading is forbidden, and it is banned to use forks to lift workers to participate in high-altitude procedures to stay clear of high-altitude dropping accidents. .
9. It is not allowed to utilize the brake inertia to slip, place, round or roll items. .
10. It is not permitted to make use of forks to select, transform pallet unload.

Leaving .
1. It is forbidden to leave the forklift when the items on the fork are in the air. Before leaving the forklift, you should discharge the goods or lower the fork framework.
2. Pull the emergency brake manage to dead or dispirit the emergency brake button.
3. The engine is shut off and the power is cut off. (Except for special situations, such as the motorist does not leave the automobile's line of vision and does not surpass 1 minute).
4. Remove the key. .

Forklift Operation Precautions.
1. Before and after the forklift procedure, the look should be checked, and gas, lubing oil and air conditioning water ought to be Stand-on Electric Pallet Stacker added.
2. Check the safety efficiency of beginning, running and braking.
3. Check whether the lights and horn signals are complete and reliable.
4. Throughout the operation of the forklift, check whether the stress and temperature level are typical.
5. After the forklift is running, the outside leakage needs to additionally be inspected and the seals ought to be replaced in time.

Forklift Safety Operation Specifications.
1. You have to inspect before leaving the vehicle;.
2. When you encounter a person in front of you during driving, you need to send a signal at a distance of 5 m;.
3. The driving speed in the manufacturing facility does not surpass 5 km/h;.
4. When driving, the low point of the freight ought to be 0.3 m ~ 0.4 m in the air;.
5. The transforming should not be also sharp to avoid the propensity of " complimentary turning";.
6. Adding and down the slope needs to be sluggish and uniform, and no activating the slope is permitted.
7. Do not drive across Electric Forklift Truck for Warehouse the slope. When the gradient is more than 10%, the car should be driven in reverse when going downhill;.
8. When the forklift workers carry the goods and progress, if they encounter big or heavy products and most likely to the chauffeur's view, they ought to take the turning around exercise
.
The "Eight Prohibitions" must be followed in the operation.
1. Solitary fork procedure is not enabled.
2. It is not permitted to lift the goods for far away driving.
3. It is not allowed to get the goods by passing on the pallet with the fork.
4. It is not allowed to directly shovel chemicals, flammables and various other hazardous chemicals with forks.
5. It is not enabled to make use of inertia force to pick up the goods.
6. It is not enabled to make use of braking force to expatriation round or easy-to-roll things.
7. It is not allowed to bring people to service the pallet or fork, and it is purely forbidden to stand under the fork after the fork is increased.
8. Do not drive side to side on inclines
.
Car parking is not allowed under the list below problems.
1. Contours, narrow roads, railway crossings;.
2. Sections with a longitudinal incline more than 5%.
3. When there is an obstacle on one side of the road, the opposite side of the section with the exact same size as the barrier need to be within 20 meters at each end.

Web：https://www.onenforklifts.com/
Email：[email protected]
Phone：+86 13827083844